Author |
Topic |
|
LewPalmer
USA
3208 Posts |
Posted - 22/10/2021 : 18:52:02
|
Again I'm looking for a few more parts to progress the resuscitation of NA0651:
Distributor (DQH6A or DUH6A) found Pitman (steering drop) Arm - can be from PA/B, TA, TB. or TC found Clutch Driven Plate - NA or PA or PB found "top hat" piece from front of crank - S&V show it opposite page 24 as part E3/18 but don't list it. found
My budget is limited so If I hit pay dirt, I may not be able to buy everything at once, but any help is greatly appreciated.
Lew Palmer PA1169, 2M1281, NA0651 |
Edited by - LewPalmer on 04/02/2022 22:52:53 |
|
George Eagle
United Kingdom
3226 Posts |
Posted - 22/10/2021 : 20:41:19
|
Hi Lew
I have a couple of steering drop arms, will check and give you the details.
George Ex NA0960 |
|
|
LewPalmer
USA
3208 Posts |
Posted - 22/10/2021 : 23:29:44
|
Thanks, George
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
George Eagle
United Kingdom
3226 Posts |
Posted - 23/10/2021 : 10:03:36
|
Hi Lew
Email sent - I have only the one drop arm, photos sent by email.
George |
|
|
LewPalmer
USA
3208 Posts |
Posted - 02/11/2021 : 18:05:44
|
Drop arm now sorted. But I'm still looking for - the distributor - the front crank piece - and especially the P or N clutch driven plate
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
treetops
Netherlands
284 Posts |
Posted - 04/11/2021 : 11:34:22
|
Hi Lew,
I have a spare DQH6 distributor type A68. I know that the "A" for anti clockwise is missing . If you it is of interest to you send me an email Regards
Jos
|
|
|
rapide
United Kingdom
238 Posts |
Posted - 04/11/2021 : 11:41:26
|
I would be interested also . Is it complete with cap and Rotor . Is it old and worn or good..?
regards Garry
Ps I have a N type spare wheel carrier if you are still looking |
Edited by - rapide on 04/11/2021 12:06:10 |
|
|
ross mullen
Canada
5 Posts |
Posted - 04/11/2021 : 16:46:15
|
Lew :I a sending pictures of left over parts from NB0895.
Ross Mullen |
|
|
LewPalmer
USA
3208 Posts |
Posted - 04/11/2021 : 18:28:21
|
Response sent, Jos
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
LewPalmer
USA
3208 Posts |
Posted - 07/11/2021 : 22:06:46
|
Distributor now sorted, now down to a PA or NA driven disk. Anybody??
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
Bruce Sutherland
United Kingdom
1543 Posts |
Posted - 07/11/2021 : 22:24:51
|
Lew, Re your quote ""top hat" piece from front of crank - S&V show it opposite page 24 as part E3/18 but don't list it."
My S&V catalogue, page 21, lists Illustration Nos. E2-18 & E3-18 Crankshaft thrust washer, hardened and ground, as S&V Part No.: 1362.
Bruce. (PB0564) |
|
|
LewPalmer
USA
3208 Posts |
Posted - 07/11/2021 : 22:45:45
|
I know, Bruce. It's been a long while since I restored my PA which has a similar albeit bigger engine, so I don't remember how things went together. I don't recall having a similar piece, but I could be wrong. A REALLY detailed drawing or better yet a detailed photo showing the parts and the order of assembly would be immensely helpful. I was lucky enough to acquire two new white metal thrust washers, but no skew or bevel gears yet, so I am still confused on what is still needed and correct.
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
mgmog
United Kingdom
460 Posts |
|
LewPalmer
USA
3208 Posts |
Posted - 08/11/2021 : 19:09:24
|
That's it exactly, Rich. I'll check with S&V on my next order to see if they have them.
Had I been able to find the thread when I built up my PA engine, I wouldn't have needed to ask the same all over again.
So thanks all!
Lew Palmer PA1169, 2M1281, NA0651 |
Edited by - LewPalmer on 08/11/2021 23:00:10 |
|
|
LewPalmer
USA
3208 Posts |
Posted - 03/12/2021 : 18:27:01
|
I'm back on the trail for a distributor. I have received a distributor marked DQH6 (not DQH6A), but I'm confused. The body is shorter that what I expected and does not appear to have been cut off. The base plate has been mounted into the very bottom of the body and it has no advance mechanism. So I need some advice and help, Could someone send me information and possibly photos: 1) Does this sound like anything with which you may be familiar? 2) Did Lucas ever make a DQH6 distributor that use a Bakelite baseplate that sat on top of the cast metal body? 3) Can anyone send photos of such a distributor, including the advance mechanism and base plate?
This is what mine looks like:
Lew Palmer PA1169, 2M1281, NA0651 |
|
|
|
Topic |
|